By the time the first hard freeze arrives in De Pere, Appleton, and Green Bay, the same questions start hitting our call center. Some are about a noise or a smell, some about a thermostat setting, and a few about whether a new heat pump can handle a Wisconsin January. Here are the ones that come up most, answered with what’s happening inside the equipment.

Why does the air from my vents feel cool when the heat first comes on?

On a gas furnace, this is usually normal. The burners light first, and the blower waits until the heat exchanger has warmed up, typically 30 to 90 seconds, so it doesn’t push cold air through the house. Once the blower starts, the air should turn warm within a minute or two.

If the air stays cool, something is stopping the burners or the heat from reaching the ducts. A flame sensor coated with residue shuts the burners off after a few seconds and tries again. Clogged filters let the heat exchanger overheat, and the safety limit switch cuts the burners. A thermostat fan setting left on “ON” also moves unheated air through the ducts between heating cycles. Heat pumps are a separate case: their supply air runs around 90 to 100 degrees, which is warmer than the room but cooler than skin temperature, so it feels cool on your hand even when the system is working correctly. A heating maintenance visit inspects the flame sensor and checks airflow, which are the usual causes of a furnace that starts and then goes cold.

Is it normal for my furnace to run almost nonstop in January?

On the coldest days, yes. A furnace is sized for the design day, the cold end of the local winter, and on that day it should run in long cycles because the house is losing heat as fast as the furnace can replace it. De Pere nights can fall to single digits and below, and a furnace running 15 to 20 minutes at a time, or close to continuously, through those nights is doing its job.

Constant running becomes a warning sign when the house won’t reach the thermostat setting, when the runtime has climbed compared with the same temperatures last winter, or when the gas bill jumps without a colder month to explain it. A dirty filter, weak airflow, a failing burner, or ducts leaking into an unheated basement can all cause it. Short cycles of two or three minutes are the opposite problem and point to a limit switch, a flame sensor, or an oversized unit.

What should I set the thermostat to during a Wisconsin winter?

Most households settle between 66 and 70 degrees while home, and 68 is a common starting point. The savings come from setting it back while nobody is home or everyone is asleep. The Department of Energy puts the savings at up to about 10 percent a year for turning the thermostat back 7 to 10 degrees for eight hours a day.

How much setback suits your house depends on the equipment. A gas furnace recovers quickly, so a deeper setback pays off. A boiler or radiant floor holds a lot of heat in water and concrete and responds slowly, so smaller setbacks timed ahead of waking up work better. A heat pump does best with modest changes. When the house will be empty for days, 55 degrees keeps the pipes safe. Healthy Home installs smart thermostats that learn your schedule and can run zones separately, so rooms nobody uses don’t draw heat all day.

Do heat pumps work when it’s below zero?

Modern heat pumps do, with limits worth knowing. Cold-climate heat pumps are designed to keep working well below freezing, and Healthy Home’s heat pump page says modern units are designed to operate efficiently in colder climates like Wisconsin. Their output drops as the outdoor temperature falls, though, and the house keeps losing heat faster the colder it gets. In a cold snap, that is where a backup heat source comes in, and it is the part of the installation worth asking about before you buy.

Two things you may see on a cold morning are normal. The outdoor unit periodically runs a defrost cycle, melting frost off the coil, and releases a puff of steam while it does. And the supply air is cooler than a furnace’s, as above. Keep snow and ice cleared from around the outdoor unit so air can reach the coil.

What indoor humidity should I aim for in winter?

Between 30 and 40 percent suits most Wisconsin homes, closer to 30 on the coldest days and nearer 40 in milder weather. The reason is condensation: warm indoor air carrying too much moisture hits cold window glass and turns to water, then frost, and can run down into the frame and feed mold. Foggy windows, damp corners, and peeling window trim all mean the house is holding too much moisture for the outdoor temperature.

Too little causes the opposite set of complaints, including static shocks, dry skin and sinuses, and cracks opening in hardwood floors. Winter heating is the reason, since cold outdoor air holds almost no moisture and warms to a very dry indoor level. A whole-house humidifier works through the existing furnace ductwork to add moisture and adjusts as the weather changes, which Healthy Home offers through its indoor air quality services.

How do I know when it’s time to replace my furnace instead of repairing it?

Age is the first signal. Properly maintained furnaces last around 10-12 years, or earlier if they were not properly maintained. Frequent or increasing repair visits indicate a replacement should be a strong consideration. A cracked heat exchanger ends the repair question, because it can’t be fixed and it is a carbon monoxide risk.

The second signal is what each repair buys you. A repair that costs a large share of a new system, on a furnace in its late teens, is money spent on borrowed time, and the gas bill from an older 80 percent unit keeps running higher than a 95 percent one would. Newer high-efficiency furnaces vent through plastic pipe out the side of the house and drain condensate, which means a few installation details that an older unit didn’t have. Most furnace installations are finished in a single day, and Healthy Home offers financing through Synchrony Bank for those who want to spread out the cost.

What should I do when the heat stops working on a cold night?

Start with the quick checks that fix a surprising share of no-heat calls. Confirm the thermostat is set to heat, with a setting above the room temperature, and that the batteries are fresh. Find the furnace’s power switch, which looks like a light switch on or near the unit, and make sure it’s on. Check the breaker, and look at the filter, since a badly clogged one can trip the limit switch. On a high-efficiency furnace, a frozen or blocked condensate drain will shut the unit down.

If those don’t help, stop there. A rotten-egg or gas smell means leave the house and call the gas utility and 911 from outside, without touching light switches. A carbon monoxide alarm sounding means getting everyone outside first. Otherwise, keep the house as warm as you can, open the cabinet doors under sinks on outside walls, and call. Healthy Home offers 24/7 emergency furnace repair, and a repair visit is far less disruptive when it is not also a frozen-pipe call.

Questions Worth Answering Before the Cold Arrives

Most of the problems above show up first as a small change, such as a longer cycle, a cooler register, or a window that fogs for the first time. Healthy Home’s Peace of Mind maintenance program schedules the checks that catch those changes before they turn into an emergency call.

If your system is doing something on this list, contact Healthy Home Heating and Cooling or call (920) 659-4735 today and have a technician take a look before the next cold snap.

company icon
Categories: